Troubleshooting Apache Kudu

Kudu requires hole punching capabilities in order to be efficient. Hole punching support depends upon your operation system kernel version and local filesystem implementation.

• RHEL or CentOS 6.4 or later, patched to kernel version of 2.6.32-358 or later. Unpatched RHEL or CentOS 6.4 does not include a kernel with support for hole punching.

• Ubuntu 14.04 includes version 3.13 of the Linux kernel, which supports hole punching.

• Newer versions of the ext4 and xfs filesystems support hole punching. Older versions that do not support hole punching will cause Kudu to emit an error message such as the following and to fail to start:

  Error during hole punch test. The log block manager requires a
  filesystem with hole punching support such as ext4 or xfs. On el6,
  kernel version 2.6.32-358 or newer is required. To run without hole
  punching (at the cost of some efficiency and scalability), reconfigure
  Kudu with --block_manager=file. Refer to the Kudu documentation for more
  details. Raw error message follows.

Without hole punching support, the log block manager is unsafe to use. It won’t ever delete blocks, and will consume ever more space on disk.

If you can’t use hole punching in your environment, you can still try Kudu. Enable the file block manager instead of the log block manager by adding the --block_manager=file flag to the commands you use to start the master and tablet servers. The file block manager does not scale as well as the log block manager.

When Kudu starts, it checks each configured data directory, expecting either for all to be initialized or for all to be empty. If a server fails to start with a log message such as the following, then this precondition check has failed.

Check failed: _s.ok() Bad status: Already present: FS layout already exists; not overwriting existing layout: FSManager roots already exist: /data0/kudu/data

This could be because Kudu was configured with non-empty data directories on first startup, or because a previously-running, healthy Kudu process was restarted and at least one data directory was deleted or is somehow corrupted, perhaps because of a disk error. If it is the latter, refer Changing Directory Configuration.

For the master and tablet server daemons, the server’s clock must be synchronized using NTP. In addition, the maximum clock error(not to be mistaken with the estimated error) must be below a configurable threshold. The default value is 10 seconds, but it can be set with the flag --max_clock_sync_error_usec.

If NTP is not installed, or if the clock is reported as unsynchronized, Kudu will not start, and will emit a message such as:

F0924 20:24:36.336809 14550 hybrid_clock.cc:191 Couldn't get the current time: Clock unsynchronized. Status: Service unavailable: Error reading clock. Clock considered unsynchronized.

If NTP is installed and synchronized, but the maximum clock error is too high, the user will see a message such as:

Sep 17, 8:13:09.873 PM FATAL hybrid_clock.cc:196 Couldn't get the current time: Clock synchronized, but error: 11130000, is past the maximum allowable error: 10000000

or

Sep 17, 8:32:31.135 PM FATAL tablet_server_main.cc:38 Check failed: _s.ok() Bad status: Service unavailable: Cannot initialize clock: Cannot initialize HybridClock. Clock synchronized but error was too high (11711000 us).

Kudu has a hard and soft memory limit. The hard memory limit is the maximum amount a Kudu process is allowed to use, and is controlled by the --memory_limit_hard_bytes flag. The soft memory limit is a percentage of the hard memory limit, controlled by the flag memory_limit_soft_percentage and with a default value of 80%, that determines the amount of memory a process may use before it will start rejecting some write operations.

If the logs or RPC traces contain messages such as the following example, then Kudu is rejecting writes due to memory back pressure. This may result in write timeouts.

Service unavailable: Soft memory limit exceeded (at 96.35% of capacity)

There are several ways to relieve the memory pressure on Kudu:

• If the host has more memory available for Kudu, increase --memory_limit_hard_bytes.

• Increase the rate at which Kudu can flush writes from memory to disk by increasing the number of disks or increasing the number of maintenance manager threads --maintenance_manager_num_threads. Generally, the recommended ratio of maintenance manager threads to data directories is 1:3.

• Reduce the volume of writes flowing to Kudu on the application side.

Finally, check the value of the --block_cache_capacity_mb setting. This setting determines the maximum size of Kudu's block cache. While a higher value can help with read and write performance, setting it too high as a percentage of the --memory_limit_hard_bytes setting is harmful. Do not raise --block_cache_capacity_mb above --memory_pressure_percentage (default 60%) of --memory_limit_hard_bytes, as this will cause Kudu to flush aggressively even if write throughput is low. The recommended value for --block_cache_capacity_mb is below the following:

(50% * --memory_pressure_percentage) * --memory_limit_hard_bytes

With the defaults, this means the --block_cache_capacity_mb should not exceed 30% of --memory_limit_hard_bytes.

For advanced debugging of memory usage, administrators may enable heap sampling on Kudu daemons. This allows Kudu developers to associate memory usage with the specific lines of code and data structures responsible. When reporting a bug related to memory usage or an apparent memory leak, heap profiling can give quantitative data to pinpoint the issue.

To enable heap sampling on a Kudu daemon, pass the flag --heap-sample-every-n-bytes=524588. If heap sampling is enabled, the current sampled heap occupancy can be retrieved over HTTP by visiting http://tablet-server.example.com:8050/pprof/heap or http://master.example.com:8051/pprof/heap. The output is a machine-readable dump of the stack traces with their associated heap usage.

Rather than visiting the heap profile page directly in a web browser, it is typically more useful to use the pprof tool that is distributed as part of the gperftools open source project. For example, a developer with a local build tree can use the following command to collect the sampled heap usage and output an SVG diagram:

thirdparty/installed/uninstrumented/bin/pprof -svg  'http://localhost:8051/pprof/heap' > /tmp/heap.svg

The resulting SVG may be visualized in a web browser or sent to the Kudu community to help troubleshoot memory occupancy issues.

For better scalability on nodes hosting many replicas, we recommend that you use nscd (name service cache daemon) to cache both DNS name resolution and static name resolution (via /etc/hosts).

When DNS lookups are slow, you will see a log message similar to the following:

W0926 11:19:01.339553 27231 net_util.cc:129] Time spent resolving address for kudu-tserver.example.com: real 4.647s user 0.000s sys 0.000s

nscd can alleviate slow name resolution by providing a cache for the most common name service requests, such as for passwords, groups, and hosts.

Refer to your operating system documentation for how to install and enable nscd.

Consult your operating system's documentation for how to install and enable nscd.

You will encounter this exception when you try to access a Kudu table using Hive. This is not a case of a missing jar, but simply that Impala stores Kudu metadata in Hive in a format that is unreadable to other tools, including Hive itself. and Spark. Currently, there is no workaround for Hive users. Spark users can work around this by creating temporary tables.